SPI Magnetic sensor setup

In order to use your SPI magnetic position sensor with SimpleFOClibrary first create an instance of the MagneticSensorSPI class:

// MagneticSensorSPI(int cs, float _cpr, int _angle_register)
//  cs              - SPI chip select pin 
//  bit_resolution - magnetic sensor resolution
//  angle_register  - (optional) angle read register - default 0x3FFF
MagneticSensorSPI sensor = MagneticSensorSPI(10, 14, 0x3FFF);

The parameters of the class are

chip_select - pin number you connected your sensor to be used with the SPI communication,
bit_resolution - resolution of your sensor (number of bits of the sensor internal counter register) and your
angle register - register number containing angle value.
The default angle_register number is set to 0x3FFF as it is the angle register for most of the low cost AS5048/AS5047 sensors.

Additionally the library allows you to configure SPI communication clock speed and SPI mode by setting the variables:

// spi mode (phase/polarity of read/writes) i.e one of SPI_MODE0 | SPI_MODE1 (default) | SPI_MODE2 | SPI_MODE3
sensor.spi_mode = SPI_MODE0;
// speed of the SPI clock signal - default 1MHz
sensor.clock_speed = 500000;

Finally after the configuration the only thing you need to do is to call the init() function. This function prepares the SPI interface and initializes the sensor hardware. So your magnetic sensor initialization code will look like:

MagneticSensorSPI sensor = MagneticSensorSPI(10, 14, 0x3FFF);

void loop(){
  ...
  sensor.spi_mode = SPI_MODE0; // spi mode - OPTIONAL
  sensor.clock_speed = 500000; // spi clock frequency - OPTIONAL
  sensor.init();
  ...
}

If you wish to use more than one magnetic sensor, make sure you connect their chip_select pins to different arduino pins and follow the same idea as above, here is a simple example:

MagneticSensorSPI sensor1 = MagneticSensorSPI(10, 14, 0x3FFF);
MagneticSensorSPI sensor1 = MagneticSensorSPI(9, 14, 0x3FFF);

void loop(){
  ...
  sensor1.init();
  sensor2.init();
  ...
}

Multiple SPI busses

For the microcontrollers where that is possible, library provides you a way to provide it the SPI bus you would like it to use instead of default SPI class.

// these are valid pins (mosi, miso, sclk) for 2nd SPI bus on storm32 board (stm32f107rc)
SPIClass SPI_2(PB15, PB14, PB13);
void setup(){
  // init magnetic sensor   
  sensor.init(&SPI_2);
}

Quick configuration for common sensors

For the most common SPI magnetic sensors, the library provides the simplified configuration constructor. Namely for AS5047/AS5147 14-bit SPI sensors and MA70 14-bit SSI sensor.

// instance of AS5047/AS5147 sensor
MagneticSensorSPI sensor = MagneticSensorSPI(10, AS5147_SPI);
// instance of MA730 sensor
MagneticSensorSPI sensor = MagneticSensorSPI(10, MA730_SPI);

If wish to implement your own quick configuration structure, you will need to create an instance of the structure:

struct MagneticSensorSPIConfig_s  {
  int bit_resolution;
  int angle_register;
  int spi_mode; // default SPI_MODE0
  long clock_speed;  // default 1MHz
  int data_start_bit; // default 13
  int command_rw_bit; // default 14
  int command_parity_bit; // default 15
};

and provide it to the constructor, here is an example:

// 12 bit, 0x3FFF angle register, spi mode 1, 1MHz, default start bit, rw command, and parity bit 
MagneticSensorSPIConfig_s MySensorConfig = {
  .bit_resolution=12, 
  .angle_register=0x3FFF, 
  .spi_mode=SPI_MODE1, 
  .clock_speed=1000000, 
  .data_start_bit=13,
  .command_rw_bit=14,
  .command_parity_bit=15
  }; 

// the sensor class with desired sensor configuration
MagneticSensorSPI sensor = MagneticSensorSPI(10, MySensorConfig);
void setup(){
  sensor.init();
  ...
}

Please check the magnetic_sensor_spi_example.ino example for a quick test of your sensor. All the features of SPI magnetic sensors are implemented in the MagneticSensorSPI.cpp/h files.

Using magnetic sensor in real-time

There are two ways to use magnetic sensor implemented within this library:

As motor position sensor for FOC algorithm
As standalone position sensor

Position sensor for FOC algorithm

To use the ensor with the FOC algorithm implemented in this library, once when you have initialized sensor.init() you just need to link it to the BLDC motor by executing:

motor.linkSensor(&sensor);

Standalone sensor

To get the magnetic sensor angle and velocity at any given time you can use the public methods:

class MagneticSensorSPI{
 public:
    // shaft velocity getter
    float getVelocity();
  	// shaft angle getter
    float getAngle();
}

Here is a quick example for the AS5047U magnetic sensor with SPI communication:

#include <SimpleFOC.h>

// MagneticSensorSPI(int cs, float _cpr, int _angle_register)
// cs              - SPI chip select pin 
// bit_resolution  - sensor resolution
// angle_register  - (optional) angle read register - default 0x3FFF
MagneticSensorSPI as5047u = MagneticSensorSPI(10, 14, 0x3FFF);
// or quick config
MagneticSensorSPI as5047u = MagneticSensorSPI(10, AS4147_SPI);

void setup() {
  // monitoring port
  Serial.begin(115200);

  // initialise magnetic sensor hardware
  as5047u.init();

  Serial.println("as5047u ready");
  _delay(1000);
}

void loop() {
  // display the angle and the angular velocity to the terminal
  Serial.print(as5047u.getAngle());
  Serial.print("\t");
  Serial.println(as5047u.getVelocity());
}